Author Topic: Flash hole deburring  (Read 10502 times)

rat31465

  • Jack of all Trades, Master of none.
  • Top Forum Member
  • *****
  • Posts: 256
  • Liked:
  • Likes Given: 0
Re: Flash hole deburring
« Reply #10 on: January 05, 2011, 08:33:18 AM »

I have to wonder effect does decapping the brass have on getting rid of the burr. ???

Good Question...I would be interested in in seeing before and after pics if you follow up on that.
"Get yourself a Glock and Lose that Nickle Plated Sissy Pistol."
Sam Gerard

Tyler Durden

  • Top Forum Member
  • *****
  • Posts: 992
  • Liked:
  • Likes Given: 4
Re: Flash hole deburring
« Reply #11 on: January 06, 2011, 12:00:52 AM »
A'yup, I will see what I can do.

I did cut off the headstamp region of one of my .223 cases and there was quite the burr left by the punching process.

Pecos Bill

  • Top Forum Member
  • *****
  • Posts: 461
  • Liked:
  • Likes Given: 0
Re: Flash hole deburring
« Reply #12 on: January 06, 2011, 01:06:31 PM »
Just checked some of my Starline brass .... don't see any burrs. From what I understand Starline uses a process that eliminates the burrs. Just a thought.

Pecos
"Suppose you were an idiot. And suppose you were a member of Congress, but I repeat myself." - Mark Twain

billt

  • Top Forum Member
  • *****
  • Posts: 6751
  • Liked:
  • Likes Given: 475
Re: Flash hole deburring
« Reply #13 on: February 14, 2011, 04:55:01 PM »
The only flash holes I'll deburr is for my .308 and .300 Win. Mag. long range target rifles. I honestly don't know if it helps or not. I figure that if I'm being totally anal with all of my case prep, I might as well go all the way and do it, thereby leaving nothing to chance. With Lapua brass the flash hole is drilled not punched, so the burr is little to non existent. I can't see the purpose of doing it for pistol ammunition.  Bill T.

bbbean

  • Very Active Forum Member
  • ****
  • Posts: 133
  • Liked:
  • Likes Given: 0
Re: Flash hole deburring
« Reply #14 on: February 14, 2011, 05:07:16 PM »
I debur mine with a small charge of explosives under pressure. In point of fact, I de-burr between 100-500 cases each practice and 100-300 each match.
--
Barry Bean
Fastest of the slow shooters, best of the bad shots

Sponsor

  • Guest
Re: Flash hole deburring
« Reply #15 on: Today at 11:28:26 PM »

MikeBjerum

  • Top Forum Member
  • *****
  • Posts: 10996
  • DRTV Ranger
  • Liked:
  • Likes Given: 1143
Re: Flash hole deburring
« Reply #15 on: June 13, 2011, 08:59:59 AM »
The only flash holes I'll deburr is for my .308 and .300 Win. Mag. long range target rifles. I honestly don't know if it helps or not. I figure that if I'm being totally anal with all of my case prep, I might as well go all the way and do it, thereby leaving nothing to chance. With Lapua brass the flash hole is drilled not punched, so the burr is little to non existent. I can't see the purpose of doing it for pistol ammunition.  Bill T.

I'm with Billt.

I'm just getting into rifle reloading, and I have read a lot both ways.  However, I figure if I am going to be this anal about so many steps why not go all the way.  There are few jobs that can be done while doing other things (watching tv, listening to a game on the radio, or between rounds at a match), and this is one of them.  Plus, you only need to do it once on a piece of brass, and it is good for life.
If I appear taller than other men it is because I am standing on the shoulders of others.

 

SMF spam blocked by CleanTalk