Author Topic: looking for a lower parts kit.  (Read 20656 times)

tombogan03884

  • Guest
Re: looking for a lower parts kit.
« Reply #10 on: April 17, 2013, 06:45:45 PM »
You need to keep in mind the possibility of feeding issues with standard magazines if you to to odd ball.

twyacht

  • "Cogito, ergo armatum sum."
  • Top Forum Member
  • *****
  • Posts: 10419
  • DRTV Ranger
  • Liked:
  • Likes Given: 0
Re: looking for a lower parts kit.
« Reply #11 on: April 17, 2013, 07:48:19 PM »
You need to keep in mind the possibility of feeding issues with standard magazines if you to to odd ball.


TAB's typing skills must be contagious Tom... ;)

Good luck with the odd ball TAB,...mags, and bolts maybe a pricey addition, but if it's where you want to go,....may I humbly consider .50 Beowulf, or .458 SOCOM?  Ammo prices are bad enough...

or just get the 9mm conversion for cost.....which also NOW sucks.



Thomas Jefferson: The strongest reason for the people to keep and bear arms is, as a last resort, to protect themselves against the tyranny of government. That is why our masters in Washington are so anxious to disarm us. They are not afraid of criminals. They are afraid of a populace which cannot be subdued by tyrants."
Col. Jeff Cooper.

TAB

  • Top Forum Member
  • *****
  • Posts: 9884
  • Liked:
  • Likes Given: 85
Re: looking for a lower parts kit.
« Reply #12 on: April 17, 2013, 08:26:25 PM »
if I keep it something based off the 222( yes 222 not 223. 222 Is the parent of 223) or a standard hand gun cal.   none of that should be a prob.   might need a custom barrel or have on reemed out.   no big deal.
I always break all the clay pigeons,  some times its even with lead.

tombogan03884

  • Guest
Re: looking for a lower parts kit.
« Reply #13 on: April 17, 2013, 08:30:18 PM »
You may need to mess with springs to adjust for more or less recoil .
Maybe even adjust the gas port.

TAB

  • Top Forum Member
  • *****
  • Posts: 9884
  • Liked:
  • Likes Given: 85
Re: looking for a lower parts kit.
« Reply #14 on: April 17, 2013, 10:21:12 PM »
I would think just springs would be enough.  Depends on how crazy it goes.   you might need to mess with the gas port, but I would think you can control when the gun unlocks with just springs. 
I always break all the clay pigeons,  some times its even with lead.

Sponsor

  • Guest
Re: looking for a lower parts kit.
« Reply #15 on: Today at 04:59:13 PM »

tombogan03884

  • Guest
Re: looking for a lower parts kit.
« Reply #15 on: April 18, 2013, 02:06:19 PM »
Depending on the power difference in the cartridge you may need either earlier  or later ejection.
That is based on when the casing retracts from the chamber wall, and it would require larger, or smaller gas port.

Big Frank

  • NRA Benefactor Member
  • Top Forum Member
  • *****
  • Posts: 8250
  • DRTV Ranger
  • Liked:
  • Likes Given: 437
Re: looking for a lower parts kit.
« Reply #16 on: April 18, 2013, 04:02:14 PM »
A pistol cartridge like that in an AR should function with blowback operation.
""It may be laid down as a primary position, and the basis of our system, that every Citizen who enjoys the protection of a free Government, owes not only a proportion of his property, but even his personal services to the defence of it, and consequently that the Citizens of America (with a few legal and official exceptions) from 18 to 50 Years of Age should be borne on the Militia Rolls, provided with uniform Arms, and so far accustomed to the use of them, that the Total strength of the Country might be called forth at a Short Notice on any very interesting Emergency." - George Washington. Letter to Alexander Hamilton, Friday, May 02, 1783

THE RIGHT TO BUY WEAPONS IS THE RIGHT TO BE FREE - A. E. van Vogt, The Weapon Shops of Isher

TAB

  • Top Forum Member
  • *****
  • Posts: 9884
  • Liked:
  • Likes Given: 85
Re: looking for a lower parts kit.
« Reply #17 on: April 18, 2013, 04:11:10 PM »
the 9x25 dillon is pretty damn hot, its pretty close to a low power rifle.
I always break all the clay pigeons,  some times its even with lead.

Rastus

  • Mindlessness Fuels Tyranny
  • Top Forum Member
  • *****
  • Posts: 6402
  • DRTV Ranger
  • Liked:
  • Likes Given: 332
Re: looking for a lower parts kit.
« Reply #18 on: September 30, 2013, 07:41:24 PM »
Did you ever finish the thing?
Necessity is the plea for every infringement of human freedom.
It is the argument of tyrants; it is the creed of slaves.
-William Pitt, British Prime-Minister (1759-1806)
                                                                                                                               Avoid subjugation, join the NRA!

TAB

  • Top Forum Member
  • *****
  • Posts: 9884
  • Liked:
  • Likes Given: 85
Re: looking for a lower parts kit.
« Reply #19 on: September 30, 2013, 09:28:28 PM »
half way, got a trigger group and all the other lower bits.   then the truck finally gave out and i need to save for a newer one.
I always break all the clay pigeons,  some times its even with lead.

 

SMF spam blocked by CleanTalk